Used Weinig Luxscan C180 Scanner w/Opticut 450FJ+ & Opticut 450 Viper Optimizing Saws

Stock #8054 - Available (As Taken From Service)

 

8054-1a.jpg
8054-1a.jpg
8054-2.jpg
8054-3.jpeg
8054-4.jpg
8054-5.jpeg
8054-6.jpeg
8054-7.jpeg
8054-8.jpeg
8054-9.jpeg
8054-10.jpeg
8054-11.jpeg
8054-12.jpeg
8054-13.jpeg
8054-14.jpeg
8054-15.jpeg
8054-16.jpg
8054-17.jpg
8054-18.jpg
8054-19.jpg
8054-20.jpeg
8054-21.jpeg
8054-22.jpeg
8054-23.jpeg
8054-24.jpeg
8054-25.jpeg
8054-26.jpeg
8054-27.jpeg
8054-28.jpeg
8054-29.jpeg
8054-30.jpeg
8054-31.jpeg
8054-32.jpeg
8054-33.jpeg
8054-34.jpeg
8054-35.jpeg
8054-36.jpeg
8054-37.jpeg
8054-38.jpeg
8054-39.jpeg
8054-40.jpeg
8054-41.jpeg
8054-42.jpeg
8054-43.jpeg
8054-44.jpeg
8054-45.jpeg
8054-46.jpeg
8054-47.jpeg
Optimizing_Saw.jpg

  • Weinig Luxscan Combiscan C180 Scanner w/Opticut 450FJ+ & Opticut 450 Viper Optimizing Crosscut Saws with all Material Handling
  • Scanner installed new in 2007 and Upgraded in 2012
  • Production capacity: LF in eight (8) hours
  • COMBSICAN capable for multiple width operation at scanner and saws.
  • Multiple widths achievable existing automated movement of side camera
  • Able to process up to 300' per minute
  • 4 side detection with laser cameras – knots, pith, cracks, worm hole, wane, edge defects, etc.
  • 4 side detection for color defects – high resolution for accuracy
  • Angle cracks detection on top/bottom side
  • Optimizing software included
  • LuxOptim Optimizes the Cut Solutions of the Board Depending on the Customers Requirements
  • Dimter Opticut 450 Viper Saw # 1 (Purchased New in 2007 and upgraded in 2012)
  • 10HP, 480V, 3PH saw arbor motor
  • 3600 RPM
  • Blade Capacity: 500mm or 19.6"
  • Opticut 450 FJ+ Right Handed Through feed Optimizing Saws - Saw # 2 (Purchased New in 2012)
  • Each saw utilizes a 10HP Servo driven feed system allowing the saw to reach max acceleration of ft/min.
  • Saw Cutting Capacities
  • Incoming Board length: 24” minimum; 16’ 3” maximum
  • Board thickness: 5/8” minimum; 4.5” maximum
  • Board width: 1.625” minimum; 7.7/16” maximum
  • Board out-feed length: 6” minimum; 16’ maximum
  • Respective Material Handling Included: Dimter Powered Roll Conveyor 17'2" Long , Dimter Rake Conveyor 18'4" Long
  • Material Transfers to Dimter Scanner Chain in-feed System with one Pin Stop, Scanner in-feed belt, Scanner Out-feed belt, Dimter "Y" Transfer for feeding two saws, Dimter in-feed for each respective saw, Dimter out-feed Sort Belts with Eight(8) Pneumatic Kickers,
  • Additional in Depth Details Available Upon Request

You may also be interested in